Isolation amplifiers for norm signals and customer specified |
|||
Here you will find a general overview of all our available products. |
|||
TV1
|
|||
|
The isolation amplifiers of the series TV1 are made for the galvanic isolation resp. amplification of bipolar norm signals 0…10 V, 0…20 mA and 4…20 mA. |
||
TV2
|
|||
|
The isolation amplifiers of the series TV2 are made for the galvanic isolation and converting of unipolar norm signals. The modules with a transmissionfrequency of 25Hz are also suitable for signal filtering. |
||
TV3
|
|||
|
The isolation amplifier of the series TV3 are made for the galvanic isolationOf different bipolar norm signals 0…10 V, 0…20 mA and 4…20 mA. |
||
TV4
|
|||
|
The isolation amplifiers of the series TV4 are made for the galvanic isolation and converting of unipolar norm signals. The modules with a transmission frequency of 25Hz are also suitable for signal filtering. |
||
TV5
|
|||
|
The isolation amplifiers of the series TV5 are made for the galvanic isolation and converting of unipolar norm signals 0…10 V, 0…20 mA and 4…20 mA. Themodules are characterized by their narrow design of 12,5 mm. |
||
TV6
|
|||
|
The isolation amplifiers of the series TV6 are made for galvanicisolation resp. converting of unipolar norm signals. They can be switched configured via DIP switch to 0…10V, 0…20mA and 4…20mA. If necessary are zero point and amplification adjustable by a spindle-operated potentiometer. The modules have a transmission frequencyof 25 Hz and therefore particularly suitable for signal filtering |
||
TV7
|
|||
|
The isolation amplifier of the series TV6 is specified for instant reaction up to 25kHz cut-off frequency therefore they are for special use at test stands. |
||
TV8
|
|||
|
The isolation amplifiers of the series TV8 are made customer specified and convert voltages up to 250 V or currents up to 200 mA into analog norm signals. |
||
TV9
|
|||
|
The isolation amplifiers of the series TV9 have been developed for galvanic isolation resp. amplifying of DC current- and/or voltage signals. Therefore a 3-way isolation between input- output- and supply voltage is generated. They are calibrated switchable via 8 Dip switches so that they can easily be adjusted to norm signals 0...10V, 2...10V, 0...20mA und 4...20mA for in- and output. If necessary offset and gain are fine adjustable via a 20-turn spindle-operated potentiometer. |
||
TV10
|
|||
|
The isolation amplifiers of the series TV10 have been developed for galvanic isolation of DC current- or voltage signals. Therefore a 3-way isolation between input- output- and supply voltage is generated.The isolation amplifier is available in two versions: 0...10V - 0...10V and 0(4)...20mA - 0(4)...20mA. Offset and gain are fixed. |
||
TV11
|
|||
|
The isolation amplifiers of the series TV10 have been developed for galvanic isolation of DC current- or voltage signals. Therefore a 3-way isolation between input- output- and supply voltage is generated. The isolation amplifier is available in two versions: IN: 0...10V / OUT: 0...10V and IN: 0...20mA / OUT: 0...20mA. Zero point and gain are fixed. |
||
TV17
|
|||
|
The isolation amplifiers of the series TV17 are particularly characterized of its high transmission frequency up to 25 kHz and an accuracy of 0,025%. They have been developed for the galvanic isolation resp. transformation of DC current- and / or voltage signals and are particularly suitable for using in high dynamic test stands. Therefore a 3-way isolation between input- output- and supply voltage is generated. Because of the simple construction it is not necessary to configure this unit complicated. The modules are delivered with a fixed in- and output configuration. This avoids problems during the start up. |
By using this page you accept the data privacy statement of LEG Industrie-Elektronik GmbH |